Swiveling Tripod Adapter

Making improvements to a tool we built

 

A while back, I built a couple of smartphone mounts for tripods, based on a design that came to me in a whiskey haze. That design worked very well at the main thing it was designed to do- hold a cellphone. However, in practice it has one decided weakness. Any time you attach a camera to something, you need to consider how the camera will be aimed. In my case, the thought was that the NOGA arm will be doing all the pointing, so the camera mount can be static. In practice, that didn’t work very well because the weight of the camera tends to loosen the threaded attachment point, and it’s often inconvenient to have to loosen the entire NOGA arm to rotate the camera.

If you’re not familiar with NOGA arms (or the copies thereof), they are a three-jointed arm with a single knob at the “elbow”. You can loosen the knob, arrange all three joints anywhere in space that you want, and then make the whole arm rigid in that position by tightening that single knob. They are pretty magical. Internally, they work in one of two ways. Some models have cables that run through the joints away from the elbow, and the knob acts as a sort of “winch” to tighten both of them at once, locking all the joints in position. There’s another approach whereby the whole arm is filled with fluid, and tightening the knob eliminates all air space from inside the tube/joint system, effectively locking everything up hydraulically. Both approaches work well. NOGA arms are used in machining, photography, and various other applications. In machining, they are typically attached to a magnetic base, but you also see them bolted to other equipment, or clamped to things.

Here’s an example of how “version 1” of my camera mount worked when attached to a large NOGA arm:

 

Pretty cool, right? With a NOGA arm and my Smartphone Holder, you can slap a camera anywhere. There are steel plates screwed to the walls and ceilings around my shop, and the magnetic base allows quick and easy camera positioning.

 

However, here’s the problem:

In a position like this, the phone won’t hold that angle for long. It will swing downward on its own mounting screw.

 

The problem is that the smartphone holder is effectively a long lever that gives the weight of the phone a lot of advantage over the mounting screw. No matter how tight you make it, it will always tend to unscrew itself any time the phone is held in a position where gravity would pull it to the left (lefty loosey).

A jam nut in there might help, but the other problem with this setup is that setting the camera angle is a bit inconvenient, as I mentioned before. It’s also worth noting that standard tripod threads are ¼-20, while the large NOGA arm end-effector has an M6 thread in it. These are obviously incompatible. I had “solved” that temporarily by re-cutting the threads to ¼-20 on half of an M6 bolt. Don’t do this, it’s dumb (though it did actually work).

What I’d really like is a way for the camera to be securely attached to the arm, but still be able to adjust it in space, while simultaneously adapting those mismatched threads to each other. Here’s what I came up with to do that.

 

As is tradition, I modeled this idea in Fusion 360 first. I’ll share this model and the engineering drawings for the part on my Patron feed, if anyone wants it.

 

This adapter consists of an M6-threaded rod that goes into the NOGA arm (and can be jam-nutted or Loctited as desired). This is shown in pink in the model. The other end is a smooth shaft with a channel in it. That channel holds O-rings for friction. A knurled knob (shown in yellow) fits over that shaft and is secured with setscrews. The knurled knob acts as the jam against the smartphone holder, while the smooth shaft inside allows the whole assembly to be rotated freely. The friction of the O-rings (with tension set by the setscrews) holds the phone in any orientation. The back of the knurled knob is threaded ¼-20 for fitting into any camera mount (in this case, my smartphone holder).

Okay, so that seems sane enough to work. Let’s give it a go. I’ll start by making the shaft that goes into the NOGA arm.

 

I turned the shaft down from some 360 brass, because I like this material a lot. 360 brass is an alloy with a tiny amount of lead in it, which makes it nicer to machine. It’s similar to 12L14 steel in this regard.

 

While I’m using brass, anything would work- steel, aluminum, headcheese, whatever you have. Well, headcheese would go rancid pretty quickly, so maybe don’t use that. Also, while I haven’t done a finite element analysis on it as of yet, I suspect headcheese would present some structural integrity challenges. Your mileage may vary.

 

Here’s one of my favorite quick layout tricks for machining. With the lathe spinning slowly (say, less than 100 rpm), apply layout fluid (or Sharpie) to the part. Then set your caliper to the desired length. Hook one end over the end of the part, and scribe with the other end. For this to work, the end of the part must be faced. Technically you get a teeny amount of cosine error doing this, because the caliper is at a slight angle. In practice it is such a small amount that it hardly matters.

 

Next we need to make that little groove that holds the O-rings.

 

The width of the groove is pretty arbitrary, so I made it arbitrarily the width of this parting tool. A simple plunge and the feature is formed.

 

The shaft was turned to the diameter needed by the smooth part of the shaft, but now we need to make the M6 thread. The major diameter of an M6 thread is 236 thou (6mm, shockingly), so we need to turn down that area a smidge further before cutting the threads.

 

To shave a lamb’s tail hair off the threaded area, I snuck in there with a long inside-shoulder turning tool. It needed to be long because the tailstock is in the way, but this cut is light, so rigidity won’t be a problem. The tool is sharp-pointed, which will result in a poor surface finish, but it’s going to be threaded anyway.

 

Next up is making the M6 thread. I would normally do this with a threading die in my shop-made tail-stock die holder. However, that die holder is for round dies, and the only M6 thread die I have is the hexagonal style. Fun fact- most online sources will swear that all hexagonal dies are for thread-chasing (repair), not thread cutting. This is not true. There are genuine thread-cutting dies in the hexagonal form factor. Generally thread cutting dies are round, yes, but it goes to show that most things you read on the internet are wrong. Including everything I say, perhaps. In any case, this is a good excuse to show a method of cutting threads on the lathe that doesn’t require a fancy tool. You can do it with almost any die wrench.

 

For this trick, install the die in the die wrench, then find something to center and support the back of it. In this case the wrench has a big hole in the back, so I stuck the live center in there. If that won’t work, you can also apply pressure with the end of tailstock quill directly. That will keep things straight if the back of your die wrench is flat.

 

The trick here is to put a little chunk of wood down on the ways to protect it, then allow the die wrench’s handle to rest on that. Then you can turn the lathe chuck by hand, and the threading operation will pull the die wrench forward with it, sliding along that chunk of wood. I cut all my threads this way before I made my tailstock die holder, and it works just fine. The trick with the block of wood keeps you from needing three hands for this.

 

With our threads cut, all that remains is to part it off.

 

Now we can turn our attention to the knurled knob. That part starts with a bigger chunk of brass.

 

After facing the end, I turn down the section that will form the socket for the spinning shaft. I do this with the “turning to a shoulder” technique I explained here on YouTube.

 

This technique is really satisfying to watch as that final face is formed, so make sure to check out the YouTube video. Watch the rest of my Lathe Skills series while you’re at it!

 

With the outer shape of the knob formed, the next task is to make the hole in the middle. We want this to be a nice slip fit over the shaft that we made earlier. When designing parts like this, you need to think about two things:

1) What tooling do you have? If you have a standard set of reamers, don’t design a feature with a 317 thou hole, because you won’t have a reamer in that size (or even a drill, for that matter). If the hole is large enough, you can use a boring operation to reach any desired size, but the hole has to be big enough to get a boring bar into. Turning can always be done to any diameter, so make your holes a standard size, and tailor the shafts that go in them to the type of fit you need (press, slip, free-running, etc). If you have over/under reamers, that makes life a lot easier. These are reamers that are 0.5 or 1 thou over (or under) their nominal size. They allow you to easily create light press fits or slip fits.

2) What is your order of operations? Holes in certain places can only be made certain ways. If the hole is coaxial with a round part, it’s likely you can ream or bore that hole as needed. If it’s a cross-hole, boring will require a very complicated setup with a faceplate, or expensive tooling like a boring head on a mill. It’s much easier if you can ream cross holes, so plan ahead for that and make your cross holes standard sizes.

 

 

Our hole will be reamed to final dimension, so we need to start by center-drilling.

 

The typical Machinist Way™ to drill a hole is to center-drill (insures concentricity), pilot drill (keeps tool pressure down and larger drills on-course), drill under-size (for reamer clearance) and finally ream to final dimension (for precision). Some of those steps can be skipped, depending on how precise the result needs to be. In our case, the hole is small, so we can skip pilot drilling, at least.

 

In this case, we’ll drill and ream. We’re going for a generous slip or free-running fit here, so our tolerances are generous. Anything from two to, say, five thousandths over will be fine.

 

A quick test fit of the shaft confirms that we’re good to go.

 

When planning order of operations, always think about the time invested in the part at critical points. If this hole had been 20 thou oversize somehow (machinist error) the part would be useless. However, we’re only on the second or third operation, so it’s not a lot of lost time. Try to arrange it so the most difficult and most critical steps are as early as possible in the order so you don’t lose much time if you have to scrap it.

Now we can flip the part and form the features on the other side of the knob. You’ll note that I’m flipping the part in the three jaw chuck here, which is a giant no-no for maintaining concentricity! Machinists are hurling invectives at their monitors right this very moment! How dare I disgrace precision this way! Okay, everyone take a deep breath. We must always consider whether maximum precision is necessary for any feature. If a tripod adapter that holds a cellphone and will never spin much at all is out-of-concentric by 5 thou due to flipping the part in a scroll chuck, I guarantee you the sun will still rise in the morning. Everyone take a deep breath and step away from the online machinist forums for a bit. Precision is almost always a tradeoff for time, and I dunno about you, but my time on this earth is the only truly valuable thing I have. If I can save some of it in a goofy side project like this, I surely will.

 

Real Machinists look away!

 

Once again, turning to a shoulder: Super Satisfying™.

 

All that’s left on this part now is to cut the ¼-20 threads for the tripod mount. Luckily for this I do have a standard round die, so I can use my tailstock die holder (which was super fun to make, by the way).

 

These threads are small and the material is brass, so this is a very easy job.

 

Next up is to apply knurling to the knob. It’s not that this knob will see much handling (you screw it into the phone holder once and pretty much never touch it again) but knurling looks nifty. It wouldn’t be a proper machinist project if something wasn’t knurled. Machinery’s Handbook (30th ed.) actually requires all parts to have something knurled. Yes, it’s true! Prove me wrong by reading the whole thing. I’ll wait.

 

Knurling close to the chuck is a very butt-clenching operation, because knurling wheels tend to wander around. I never like doing this, but for the good of you, fair blog readers, I take these bullets.

 

All we have left to do is make threaded cross holes for the set screws that hold this whole thing together. For that, I’m going over to the mill, and using one of my favorite toys: the collet block.

 

Collet blocks allow you to easily hold round parts very concentrically, and they can be indexed, which is very nice. In this case, it’s just an easy way to cross drill these two holes.

 

These set-screws are small (4-40, which is about ~2.8mm for Metric folks), so the tap is small too. Small taps means high risk of breaking them, but luckily this is just brass. A broken tap is always a sad moment, because they are so immensely hard that not much can remove them. You can’t drill them out with regular drills. Sometimes carbide drills work, if you have one the right size. In the worst cases, only Electrical Discharge Machining can save you. My $40,000 EDM machine is out for repair, so I’ll just tap carefully.

 

Taaapy tap tap…  Fun fact, it doesn’t matter which side you tap a hole from, so for a case like this, you can tap through both holes at once. That’s a bad idea unless you’re certain the holes are perfectly aligned, but we are certain of that, since we just drilled them.

 

Okay, we’re ready for some final assembly! I made the bold claim up front that this device holds the phone securely at any angle, so let’s recap how it actually does that. The answer is friction. That groove we cut in the central shaft holds some number of O-rings, which provide friction on the spinning mount. You can also tighten the setscrews as needed to set the tension. The set screws need to be in far enough to keep the knob from pulling off the shaft, but beyond that they set the amount of drag on the O-rings. You can also vary the number and thickness of the O-rings as needed for the weight they need to resist. Eventually these O-rings will wear out, but you can easily replace them by backing out the setscrews. The setscrews are not tightened all the way in, as they would lock up the shaft and crush the O-rings. Instead, they are adjusted as needed, then Loctited in place so they won’t back out. If you ever need to remove them, a little bit of heat is all that is needed to release the Loctite.

 

I experimented with thickness and quantity of O-rings until I found a combination that worked well for me.

 

Loctite is applied to the setscrews, which are then tightened in to where they are retaining the shaft inside the knob, and applying some pressure to the O-rings without crushing them.

 

I’ve been using this knob on my NOGA arm for quite a while now, and I can say it has been working quite well. I did need to Loctite the ¼-20 thread into the phone holder, because it would still unscrew itself over time as the phone was manipulated. A jam nut would also have worked here, but I like Loctite. It’s easy and it works. It remains to be seen how well the O-rings will hold up over time, but it’s been several months, and so far so good. While I designed this specifically for NOGA arms, you can easily change the thread on the shaft to allow you to mount a camera on anything you want. The power of this little guy is that you can thread in the camera mount without needing to rotate the other end, and it will hold the camera at any angle without any threads loosening.

That’s it for this project! Check out my YouTube channel to see lots of videos filmed with this very adapter!

 

 

 

2 thoughts on “Swiveling Tripod Adapter”

  1. Jim King says:

    Timo of Hydraulic Press Channel used a similar technique for threading. Great machinists think alike! https://www.youtube.com/watch?v=FKtHn8BVwnw&feature=youtu.be&t=564

    1. Quinn Dunki says:

      Wow, I wouldn’t do it under power like that, but I’m sure he knows what he’s doing. 😀 Fun video- thanks for sharing!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.